ar1440w2040r

Remove/install pump module intake filter

Typ ar · téma 14.40 · verze 0103 · 2011-03-24

Platí pro: ENGINES 926.9 in MODEL 949 with CODE (MS5) BlueTec 5

Není k dispozici v jazyce „cs“; zobrazeno v jazyce Angličtina.

Zařazení

Funkční skupina 1 Motor › 14 Sběrné výfukové potrubí, motorová brzda, zařízení pro snížení obsahu škodlivin ve výfukových plynech › 14.40 Dodatečná úprava spalin, AdBlue — Řada 949

EinPAS 15 Motor › 15.40 Výfuková soustava/dodatečná úprava výfukových plynů › 15.40.51 Čerpadlo/dávkovací jednotka/tryska — Řada 949

Platí také pro motory/převodovky: 926 9**

AR14.40-W-2040R

Remove/install pump module intake filter

22.3.11

ENGINES 926.9 in MODEL 949 with CODE (MS5) BlueTec 5

Remove/install pump module intake filter

W14.40-1427-09

1 Housing cover

2 Electrical connector

3 AdBlue line (suction)

4 Set of hoses

9 Intake filter

10 Locking piece

11 AdBlue pipe connection

12 filter screen mounting

5 Open end wrench

6 Open end wrench

7 Pump module

8 Sheet metal screw (M440)

Remove/install

Danger!

Risk of burn injuries and scalding when working at AdBlue lines and the components attached to them. Risk of injury to skin and eyes when handling AdBlue. Risk of poisoning caused by swallowing AdBlue

Pour AdBlue into suitable containers only. Wait until the pressure is released before starting any work on the exhaust aftertreatment system.

AS14.40-Z-0001-01A

Notes on use, material properties and handling of AdBlue®

AH14.40-N-0001-01A

1

Switch off ignition

2

Pull off electrical connector (2) from pump module (7)

Protect electrical connector (2) and the electrical connection at pump module (7) from escaping AdBlue solution, using plastic film or similar material.

Electrical connectors (2) and the electrical connection should not be allowed to come in contact with AdBlue, as this can cause damage to the electrical wiring harness and the SCR frame module control.

3

Check the electrical wiring harness for corrosion

AR14.40-W-2033R

4

Detach AdBlue line (3) from AdBlue inlet pipe connection (11), and close off with plug (10)

Plug (10) must be kept at hand, since AdBlue will flow out immediately when AdBlue line (3) is detached.

Installation: Replace O-rings.

Sealing piece for AdBlue intake line and AdBlue feed line

WF58.50-W-1440-05A

5

Detach housing cover (1)

Only for vehicles with pump module (7), where the counterholding hexagon nut on filter screen support fitting (12) is not outside, but behind housing cover (1).

*BA14.40-N-1047-02C

6

Remove AdBlue inlet pipe connection (11) from filter screen support fitting (12)

To remove AdBlue inlet pipe connection (11), counterhold with an open end wrench (6) on filter screen support fitting (12).

*BA14.40-N-1045-02C

7

Remove intake filter (9) from filter screen support fitting (12)

Intake filter (9) can be removed with a sheet metal screw (8).

Installation: Insert intake filter (9) carefully in filter screen support fitting (12), till the collar is seen to touch intake filter (9).

8

Install in the reverse order

Exhaust aftertreatment, Blue Tec

Number

Designation

Engine
900.9, 902.9, 924.9, 925.9, 926.9 with code MS4 or code MS5

BA14.40-N-1045-02C

AdBlue inlet fitting to filter screen support fitting

Nm

15

BA14.40-N-1047-02C

Pump module housing cover on pump module

Nm

8

Odkazované dokumenty