ar1325w3201a

Removing/installing poly-V-belt tensioning device for high-speed fan drive

Typ ar · téma 13.25 · verze 0301 · 2009-02-03

Platí pro: ENGINE 541.9 in MODEL 950, 952, 953, 954 with CODE (ML3) High-speed fan drive with belt drive ENGINE 542.9 in MODEL 950, 952, 954 with CODE (ML3) High-speed fan drive with belt drive

Není k dispozici v jazyce „cs“; zobrazeno v jazyce Angličtina.

Zařazení

Funkční skupina 1 Motor › 13 Vzduchový kompresor, řemenový převod › 13.25 Napínač řemene — Řada 950 · Řada 952 · Řada 953 · Řada 954

EinPAS 15 Motor › 15.18 Řemenový pohon › 15.18.30 Řemen/řemenice/napínací ústrojí/vratná kladka — Řada 950 · Řada 952 · Řada 953 · Řada 954

Platí také pro motory/převodovky: 541 9**, 542 9**

AR13.25-W-3201A

Removing/installing poly-V-belt tensioning device for high-speed fan drive

2.2.09

ENGINE 541.9 in MODEL 950, 952, 953, 954 with CODE (ML3) High-speed fan drive with belt drive

ENGINE 542.9 in MODEL 950, 952, 954 with CODE (ML3) High-speed fan drive with belt drive

Removing/installing poly-V-belt tensioning device for high-speed fan drive

W13.25-1009-11

Shown on a removed fan and viscous fan clutch

1 Poly-V-belt tensioning device fan

2 Poly-V-belt fan

3 Belt pulley fan drive

4 Coolant pump belt pulley

Modification notes

15.3.05

Detach coolant expansion tank on radiator and place aside - added.

Step 3

Removing/installing

Danger!

Risk of injury caused by being caught or pinched as cab is tilted

Ensure that no one is within the tilting range of the cab as it is being tilted. Always tilt the cab all the way to the end position and secure with the safety strut.

AS60.80-Z-0001-01A

1

Tilt cab

Notes on tilting the cab

AH60.80-N-0003-01A

2

Remove soundproofing on the right side of the engine

3

Remove coolant expansion tank on radiator on and place aside

Do not disconnect coolant lines.

4

Remove red charge air hose

*BA09.41-N-1006-01C

Danger!

Risk of injury caused by pinching or crushing when working on springs or spring bodies that are under load

Only use approved tensioning devices; shield off hazard area if necessary.
Inspect special tools for damage and proper operation (visual inspection).
Wear protective gloves.

AS00.00-Z-0001-01A

5

Slacken poly-V-belt for fan (2) and take it off the belt pulley of the coolant pump (4).

Installation: Inspect condition of poly-V-belt fan (2), replace if necessary.

Observe poly-V-belt routing plan.

AR13.22-W-3902-02A

Damage patterns for a poly-V-belt

AP13.22-D-1351-01A

6

Detach poly-V-belt tensioning device of fan (1) at filter housing

Installation: Insert dowel pin at the poly-V-belt tensioning device of fan (1) in the hole of the oil filter housing.

*BA13.25-N-1004-01D

7

Install in reverse order

Charge air pipe/charge air cooling

Number

Designation

Engine 541.9

Engine 542.9

BA09.41-N-1006-01C

Clamp for charge air hose on charge air housing/charge air pipe and charge air cooler

Nm

7.5

7.5

Belt tensioning device

Number

Designation

Engine
541.9, 542.9
with Code ML3

BA13.25-N-1004-01D

Bolt for poly-V-belt tensioning device on oil filter housing

Nm

45

Odkazované dokumenty