5 | Rail |
6 | High pressure pipe |
7 | High pressure pipe |
8 | Clip |
9 | Bracket |
10 | Bracket |
11 | Clip |
12 | Vibration damper |
13 | Fuel system high pressure pump |
A | Angle (approx. 15°) |
W07.16-1089-06
Danger | Risk of explosion caused by fuel igniting. Risk of injury to skin and eyes caused by fuel spraying out at high pressure | Keep all ignition sources out of hazard area. | |
Danger | Risk of explosion caused by fuel igniting, risk of poisoning caused by inhaling and swallowing fuel as well as risk of injury to eyes and skin caused by contactwith fuel. | No fires, sparks, open flames or smoking. Pour fuels into suitable and appropriately marked containers only. | |
Warning | Risk of accident from vehicle starting off by itself when engine running. Risk of injury (bruises and burns) resulting from working on the engine while it is being started or when it is running. | Secure vehicle to prevent it from starting off by itself. Wear closed and snug-fitting work clothes. Do not touch hot or rotating parts. | |
Topical note | Notes on self-locking nuts and bolts | ||
Topical note | Notes on avoiding damage through contamination and foreign objects | ||
Notes on safety-relevant components | |||
Note on calculation of tightening torque when using insertion or socket tools with various effective lengths | |||
| Remove | ||
1 | Switch off ignition. | ||
2 | Clean engine in area of high-pressure lines (6, 7). | ||
3 | Remove resonator box. | ||
4 | Remove bracket (9) on bracket (10). | ||
5 | Unscrew high-pressure lines (6, 7) on rail (5) and on fuel high-pressure pump (13). | Counterhold fitting on fuel system high pressure pump (13). | |
Ring wrench | |||
Box wrench socket | |||
6 | Remove bracket (10) on charge-air distributor and take off together with high-pressure lines (6, 7). | The bracket (10) and the high-pressure lines (6, 7) to the rail must not be reused. They must be replaced together with the clamps (8, 11) and the vibration dampers (12). | |
| Install | ||
7 | Attach new vibration dampers (12) to the new high-pressure lines (6, 7). | Screw vibration dampers (12) onto straight section of high-pressure line after first bend, observing the angle (A) of approx. 15°. | |
8 | Install new high-pressure line (6). | Union nut, high-pressure line to rail | |
Union nut, high-pressure line to fuel high-pressure pump | |||
Ring wrench | |||
Box wrench socket | |||
9 | Install new bracket (10) on charge-air distributor and on bracket (9). | ||
10 | Install new high-pressure line (7). | Union nut, high-pressure line to rail | |
Union nut, high-pressure line to fuel high-pressure pump | |||
Ring wrench | |||
Box wrench socket | |||
11 | Install new clamps (8, 11) on new bracket (10) | Bolt, high-pressure line clamp to bracket | |
12 | Install resonator box (1). | ||
13 | Start engine and perform an engine test run. | Allow the engine to run at a higher engine speed. | |
If engine fails to start or only runs for a brief period, | |||
| |||
Fill fuel low-pressure circuit. | |||
14 | Check area around high-pressure lines (6, 7) for leak tightness and switch off engine. | Visual inspection. |
314 589 01 03 00
Box wrench socket
000 589 07 03 00
Ring wrench
Odkazované dokumenty
- ah0000n000101a Upozornění k samopojistným šroubům a maticím
- ah0000n500001h Upozornění k zamezení poškozením kvůli znečistění a výskytu cizích těles
- ah0000p001501cw Pokyny pro výpočet utahovacího momentu při použití zasouvacích nebo násuvných nástrojů s různými činnými délkami
- ah0000z001901a Pokyny k bezpečnostním součástem
- ar0716g1007n
- ar1310g5840n
- as0000z000501a Nebezpečí úrazu při samovolném rozjetí vozidla při běžícím motoru. Nebezpečí poranění pohmožděním a popálením při výkonech prováděných během startování nebo při běžícím motoru
- as0716z000101b Nebezpečí výbuchu při vznícení paliva. Nebezpečí poranění kůže a očí vytékajícímpaprskem paliva
- as4700z000101a Nebezpečí výbuchu při vznícení, nebezpečí otravy při vdechnutí a požití paliva inebezpečí úrazu v důsledku přímého doteku kůže a očí s palivem