ar0715w1630h

Remove/install engine control unit (MR)

Typ ar · téma 07.15 · verze 0105 · 2008-06-20

Platí pro: ENGINES 902.9, 906.9 in MODEL 957 with CODE (MS8) natural gas engine

Není k dispozici v jazyce „cs“; zobrazeno v jazyce Angličtina.

Zařazení

Funkční skupina 1 Motor › 07 Příprava směsi › 07.15 Systém vstřikování paliva vznětového motoru (PLD), regulace motoru (MR) — Řada 902 (modely 9**) · Řada 906 (modely 9**) · Řada 957

EinPAS 15 Motor › 15.45 Management motoru › 15.45.11 Řídicí jednotka/relé — Řada 902 (modely 9**) · Řada 906 (modely 9**) · Řada 957

AR07.15-W-1630H

Remove/install engine control unit (MR)

17.6.08

ENGINES 902.9, 906.9 in MODEL 957 with CODE (MS8) natural gas engine

Remove/install engine control unit (MR)

W07.54-1005-06

1 Spacer

2 Rubber damper

3 Washer

4 Electrical connector
(vehicle wiring harness)

5 Electrical connector
(engine wiring harness)

6 Bracket

A85 MR gas engine control unit

Y87 Electric-pneumatic converter (EPW)

Remove/install

Danger!

Risk of explosion caused by escaping natural gas or overheated compressed-gas tanks when working on natural gas powered vehicles. Risk of frostbite to parts of the body caused by escaping natural gas and by touching components near the valves when emptying compressed-gas tanks. Risk of poisoning or risk of suffocation caused by inhaling natural gas.

Remove any sources of ignition.

Ensure that the work area is adequately ventilated.

Wear heat protective gloves.

AS00.00-Z-0018-01A

Notes on work safety regulations for vehicles with natural gas-powered engines

AH00.10-N-1000-04A

1

Switch off ignition

2

Open maintenance flap

Danger!

Risk of injury caused by body parts being pinched or crushed as cab is tilted

Ensure that no one is within the tilting range of the cab as it is being tilted. Always tilt the cab all the way to the end position and secure with the safety strut.

AS60.80-Z-0001-01A

3

Tilt cab

Notes on tilting the cab

AH60.80-N-0003-01A

4

Remove electropneumatic pressure converter (Y87)

AR07.17-W-0002H

5

Remove bracket (6) from gas engine (A85) control unit

*BA07.54-N-1010-01A

6

Release and disconnect electrical connectors (4, 5) at MR control unit, gas engine (A85)

Release by pressing or swiveling the release pin.

7

Remove gas engine (A85) control unit (MR) from the crankcase.

The MR control unit, gas engine (A85) must not be disassembled.

Installation: Insert all damper rubbers (2) in the gas engine control unit (MR) (A85). Observe the installation position of spacer sleeve (1) and spacer (3).

*BA07.54-N-1004-01A

8

Install in the reverse order

9

Learn all transponder keys

Only if a new gas engine (A85) control unit has been installed.

AR80.57-W-0010C

Gas injection and ignition system

Number

Designation

Engine
902.9
with code MS8,

Engine 906.9 with code MS8

BA07.54-N-1004-01A

Bolt, MR control unit to crankcase

Nm

15

BA07.54-N-1010-01A

Bolt, electropneumatic pressure converter bracket to control unit (MR)

Nm

8

Odkazované dokumenty