W07.02-1013-09
Shown on engine 470.9 |
1 | Fuel lines | 4 | Fuel system high pressure pump | 7 | Bolts | ||
2 | Fuel lines | 5 | Electrical wiring harness | 8 | Sealing rings | ||
3 | Electrical connector | 6 | Bracket | Y642 | Quantity control valve |
Danger | Risk of explosion caused by fuel igniting, risk of poisoning caused by inhaling and swallowing fuel as well as risk of injury to eyes and skin caused by contactwith fuel. | No fires, sparks, open flames or smoking. Pour fuels into suitable and appropriately marked containers only. | |
Warning | Risk of accident from vehicle starting off by itself when engine running. Risk of injury (bruises and burns) resulting from working on the engine while it is being started or when it is running. | Secure vehicle to prevent it from starting off by itself. Wear closed and snug-fitting work clothes. Do not touch hot or rotating parts. | |
Topical note | Notes on self-locking nuts and bolts | ||
Topical note | Notes on avoiding damage through contamination and foreign objects | ||
Notes on safety-relevant components | |||
Note on calculation of tightening torque when using insertion or socket tools with various effective lengths | |||
| Remove/install | ||
1 | Drain off fuel from fuel filter module. | ||
2 | Remove fuel lines (1, 2). | Installation: Install new sealing rings. | |
Flange, low pressure fuel line to fuel high-pressure pump | |||
Bolt, flange for fuel line to fuel filter module | |||
Screw, fuel line to flange for fuel high-pressure pump | |||
3 | Disconnect electrical connector (3) at quantity control valve (Y642). | ||
4 | Remove bracket (6) at fuel high-pressure pump (4) and crankcase. | Screw, fuel high-pressure pump holder to crankcase | |
Screw/nut, holder to fuel high-pressure pump | |||
5 | Unscrew screws (7). | Screw, quantity control valve to fuel high-pressure pump | |
Torque wrench | |||
6 | Remove quantity control valve (Y642) and collect escaping fuel. | Remove quantity control valve (Y642) by hand out of the housing flange for fuel system high pressure pump (4) using turning movements. Collect escaping fuel. | |
Installation: Replace sealing rings(8). Wet sealing rings (8) before installing with fuel. | |||
7 | Install in the reverse order | ||
8 | Connect vehicle diagnosis system, start diagnosis and perform quick test. | Only if the quantity control valve (Y642) has been replaced. | |
See information from body manufacturer. | |||
9 | Reset "adaptation range for quantity control valve". | Only if the quantity control valve (Y642) has been replaced. | |
The process is completely menu-assisted under: | |||
10 | End diagnosis and remove vehicle diagnosis system. | See information from body manufacturer. | |
11 | Fill fuel low-pressure circuit. | ||
12 | Start engine and perform an engine test run. | Allow the engine to run at a higher engine speed. | |
If engine fails to start or only runs for a brief period, | |||
| |||
Fill fuel low-pressure circuit again. | |||
13 | Check area of quantity control valve (Y642) for leaks and switch off engine. | Visual inspection. |
001 589 75 21 00
Torque wrench
Odkazované dokumenty
- ah0000n000101a Upozornění k samopojistným šroubům a maticím
- ah0000n500001h Upozornění k zamezení poškozením kvůli znečistění a výskytu cizích těles
- ah0000p001501cw Pokyny pro výpočet utahovacího momentu při použití zasouvacích nebo násuvných nástrojů s různými činnými délkami
- ah0000z001901a Pokyny k bezpečnostním součástem
- ar0703g146003n
- ar0716g1007n
- as0000z000501a Nebezpečí úrazu při samovolném rozjetí vozidla při běžícím motoru. Nebezpečí poranění pohmožděním a popálením při výkonech prováděných během startování nebo při běžícím motoru
- as4700z000101a Nebezpečí výbuchu při vznícení, nebezpečí otravy při vdechnutí a požití paliva inebezpečí úrazu v důsledku přímého doteku kůže a očí s palivem