W01.45-1061-09
1 | Oil pan | 4 | Oil suction pipe upper part | |
2 | Engine wiring harness | 5 | Oil suction pipe lower part | |
3 | Filler pipe | B605 | Engine oil fill level sensor |
6 | Crankcase |
7 | Housing cover |
8 | Timing case |
A | Separating points |
W01.45-1051-05
1 | Oil pan |
5 | Oil suction pipe lower part |
9 | Seal |
B605 | Engine oil fill level sensor |
W01.45-1062-05
Warning | Risk of accident from vehicle starting off by itself when engine running. Risk of injury (bruises and burns) resulting from working on the engine while it is being started or when it is running. | Secure vehicle to prevent it from starting off by itself. Wear closed and snug-fitting work clothes. Do not touch hot or rotating parts. | |
Caution | Risk of injury to skin and eyes due to handling of engine oil. Risk of poisoning caused by swallowing engine oil | Wear protective gloves, protective clothing and safety glasses. | |
Topical note | Notes on self-locking nuts and bolts | ||
Topical note | Notes on avoiding damage through contamination and foreign objects | ||
Note on calculation of tightening torque when using insertion or socket tools with various effective lengths | |||
| Remove/install | ||
1 | Drain engine oil | ||
Engine oil | |||
Drain screw on oil pan | |||
2 | Remove filler pipe (3) at oil pan (1) | Installation: Check sealing ring. | |
In case of a complaint | |||
| |||
Replace sealing ring. | |||
3 | Disconnect oil suction pipe upper part (4) at oil suction pipe lower part (5) | Installation: Check clutch. | |
In case of a complaint | |||
| |||
Replace connector . | |||
4 | Remove electrical engine wiring harness (2) on the front oil pan (1) | Screw/bolt, engine wiring harness to oil pan | |
5 | Disconnect electrical connection on engine oil fill level sensor (B605) | ||
6 | Remove oil pan (1) | Tightening procedure | |
Screw/bolts are secured against falling out in the oil pan (1). | |||
Screw/bolt, oil pan to crankcase | |||
7 | Remove seal (9) | Installation: Install new seal (9). | |
8 | Clean sealing surfaces on oil pan (1), timing case (8), crankcase (6) and front housing cover (7) | Installation: Apply sealant on separating points (A) for timing case (8) and front housing cover (7). | |
Sealant, Loctite 5970, 50 ml | |||
9 | Remove engine oil fill level sensor (B605) on the oil pan (1) | Only when replacing the oil pan (1). | |
Installation: Replace sealing ring on engine oil fill level sensor (B605). | |||
Engine oil fill level sensor to oil pan | |||
10 | Replace oil suction pipe lower part (5) | Only when replacing the oil pan (1). | |
Installation: Replace sealing ring on oil suction pipe lower part (5). | |||
11 | Install in the reverse order | ||
12 | Check/correct engine oil level | ||
13 | Start engine and perform an engine test run | Allow engine to idle; oil pressure must have built up after 10 s, then run the engine at slightly increased rpms. | |
14 | Turn off engine and check area of oil pan (1) for leaks | Visual inspection. |
Engine lubrication |
Number | Designation | ENGINE 470.9 except oil pan with front wall height 160 mm | ENGINE 470.9 with oil pan with front wall height 160 mm | ||
BF18.00-N-1001-01V | Engine oil | Filling capacity of oil pan | Liter | 31,5 | 34 |
Filling capacity of oil filter | Liter | 3 | 3 | ||
Filling capacity after repair on engine in the case of emptied oil ducts | Liter | 5 | 5 | ||
Sheet | |||||
Sheet | |||||
Sheet | |||||
Sheet | |||||
Engine lubrication |
Number | Designation | Engine 471.9 with oil pan width of 330 mm and firewall height of 225 mm | Engine 471.9 with oil pan width of 460 mm and firewall height of 120 mm | ||
BF18.00-N-1001-01V | Engine oil | Filling capacity of oil pan | Liter | 39 | 34 |
Filling capacity of oil filter | Liter | 3 | 3 | ||
Filling capacity after repair on engine in the case of emptied oil ducts | Liter | 6 | 6 | ||
Sheet | |||||
Sheet | |||||
Sheet | |||||
Sheet | |||||
Engine lubrication |
Number | Designation | Engine 471.9 with oil pan width of 470 mm and firewall height of 335 mm | Engine 471.9 with oil pan width of 530 mm and firewall height of 155 mm | ||
BF18.00-N-1001-01V | Engine oil | Filling capacity of oil pan | Liter | 36 | 36 |
Filling capacity of oil filter | Liter | 3 | 3 | ||
Filling capacity after repair on engine in the case of emptied oil ducts | Liter | 6 | 6 | ||
Sheet | |||||
Sheet | |||||
Sheet | |||||
Sheet | |||||
Engine lubrication |
Number | Designation | Engine 473.9 with rear sump oil pan with oil pan width of 350 mm | Engine 473.9 with rear sump oil pan with oil pan width of 475 mm | ||
BF18.00-N-1001-01V | Engine oil | Filling capacity of oil pan | Liter | 44 | 39 |
Filling capacity of oil filter | Liter | 3 | 3 | ||
Filling capacity after repair on engine in the case of emptied oil ducts | Liter | 8 | 8 | ||
Sheet | |||||
Sheet | |||||
Sheet | |||||
Sheet | |||||
Odkazované dokumenty
- ah0000n000101a Upozornění k samopojistným šroubům a maticím
- ah0000n500001h Upozornění k zamezení poškozením kvůli znečistění a výskytu cizích těles
- ah0000p001501cw Pokyny pro výpočet utahovacího momentu při použití zasouvacích nebo násuvných nástrojů s různými činnými délkami
- ar0145w750001h Schéma utahování šroubů olejové vany
- ar1800g303502h
- as0000z000501a Nebezpečí úrazu při samovolném rozjetí vozidla při běžícím motoru. Nebezpečí poranění pohmožděním a popálením při výkonech prováděných během startování nebo při běžícím motoru
- as1800z000101a Nebezpečí poranění očí a pokožky stykem s motorovým olejem. Nebezpečí otravy při požití motorového oleje