1 | Oil pan |
2 | Sealing (joint) |
3 | Electric connections |
4 | Oil filling line |
5 | Seal ring |
6 | Oil outlet plug |
B14 | Oil level sensor |
W01.45-1021-06
| Remove/install | ||
1 | Turn off ignition | ||
Warning | Risk of injury caused by body parts being pinched or crushed as cab is tilted | Ensure that no one is within the tilting range of the cab as it is being tilted. Always tilt the cab all the way to the end position and secure it with the safety strut. | |
2 | Tilt the cabin | ||
Topical note | Notes on tilting the cab | ||
return the cabin to its original position only after the leakiness test. | |||
3 | Remove the lower acoustic encapsulation from the chassis | Installation: install the acoustic encapsulation only after the tightness inspection. | |
4 | Drain the engine oil |
| |
Notes on engine oil | |||
Eventually, utilize the used oil collecting recipient. | |||
Installation: when the oil draining plug (6) is unscrewed, install the oil draining plug (6) with a new sealing ring (5). | |||
.Oil pan drain plug | |||
.Engine oil | |||
5 | Remove and separate the electric connections (3) at the engine control unit (MR) module | ||
6 | The oil level sensor wiring harness (B14) must remain uncovered | ||
7 | Remove the oil supply tubes (4) from the oil pan (1) | ||
8 | Remove the drive oil lines from the brackets and attach them to the side | Only for vehicles with code (N55), transmission oil cooler. Do not detach the gearbox oil lines. | |
9 | Remove the oil pan (1) | | |
Use the microencapsulated screws (3) for mounting M8x35 - N000000002815 | |||
Installation: clean the engine sealing surfaces of the engine and oil pan (1) and replace the joint (2). | |||
.Oil pan from the engine to the block | |||
10 | Modify the oil level sensor (B14) | Only when replacing the oil pan (1) | |
For retrofitting the oil level sensor (B14), use a special fitting pin (SW27). | |||
Oil level sensor in the oil pan | |||
11 | Install in reverse order | ||
Warning | Risk of accident from vehicle starting off by itself when engine running. Risk of injury (bruises and burns) resulting from working on the engine while it is being started or when it is running. | Secure vehicle to prevent it from starting off by itself. Wear closed and snug-fitting work clothes. Do not touch hot or rotating parts. | |
12 | Start the engine and leave at idle for about 10 seconds until the oil pressure is created, let the engine run at alternating speed | ||
13 | Turn the engine off and check the oil pan area (1) for tightness | ||
14 | Check the engine oil level on the display and top off as needed | ||
Notes on engine oil | |||
Note the prescribed motor oil quality in the maintenance system, or the prescribed auxiliary materials. |
Filling volume for engine lubrication |
Number | Designation | Engine 924.9, | Engine 926.9 | |||
BF18.00-B-1001-01B | Engine oil | Check the correct level | Oil pan | litros | 15,0 | 28,0 |
Filter | litros | 0,8 | 1,3 | |||
Maximum capacity after repair on the engine with drained oil channels | litros | - | - | |||
Oil class | MB 228.3, MB 228.31, 228.5, MB 228.51 | MB 228.3, MB 228.31, 228.5, MB 228.51 |
Odkazované dokumenty
- ah1800n010101ha Upozornění k motorovému oleji
- ah6080n000301a Pokyny ke sklápění kabiny řidiče
- ar1800b303502tj
- as0000z000501a Nebezpečí úrazu při samovolném rozjetí vozidla při běžícím motoru. Nebezpečí poranění pohmožděním a popálením při výkonech prováděných během startování nebo při běžícím motoru
- as6080z000101a Nebezpečí úrazu v důsledku přivření a přiskřípnutí při sklápění kabiny řidiče